Neuer problem nach update

DH1AA · December 23, 2017 at 3:35 AM

Bitte um Hilfe
Hab heute neuer SVXLINK installiert kann aber nicht starten Fehler Meldung:

Code

/usr/share/svxlink/events.tcl in logic NetLogic: missing close-brace: possible unbalanced brace in comment*** ERROR: Could not initialize Logic object "NetLogic". Skipping...Starting logic: MicLogicLoading RX: MicRx1*** ERROR: Open capture audio device failed: No such file or directory*** ERROR: Could not open audio device for receiver "MicRx1"*** ERROR: Could not initialize RX "MicRx1"*** ERROR: Could not initialize Logic object "MicLogic". Skipping...*** ERROR: No logics available. Bailing out...

Und hier mein svxlink.conf:

Code

###############################################################################
#                                                                             #
#                Configuration file for the SvxLink server                    #
#                                                                             #
###############################################################################


[GLOBAL]
MODULE_PATH=/usr/lib/arm-linux-gnueabihf/svxlink
LOGICS=SimplexLogic,NetLogic,MicLogic
CFG_DIR=svxlink.d
TIMESTAMP_FORMAT="%c"
CARD_SAMPLE_RATE=48000
#CARD_CHANNELS=1
LOCATION_INFO=LocationInfo
LINKS=LocalLink,NetLink


[SimplexLogic]
TYPE=Simplex
RX=Rx1
TX=Tx1
MODULES=ModuleHelp,ModuleParrot,ModuleEchoLink,ModuleMetarInfo
CALLSIGN=DH1AA-L
SHORT_IDENT_INTERVAL=60
LONG_IDENT_INTERVAL=60
#IDENT_ONLY_AFTER_TX=4
#EXEC_CMD_ON_SQL_CLOSE=500
EVENT_HANDLER=/usr/share/svxlink/events.tcl
DEFAULT_LANG=de_DE
RGR_SOUND_DELAY=-1
#REPORT_CTCSS=136.5
#TX_CTCSS=ALWAYS
MACROS=Macros
FX_GAIN_NORMAL=0
FX_GAIN_LOW=-12
#ACTIVATE_MODULE_ON_LONG_CMD=4:EchoLink
QSO_RECORDER=8:QsoRecorder
#ONLINE_CMD=998877
#MUTE_RX_ON_TX=1
#MUTE_TX_ON_RX=1
#STATE_PTY=/var/run/svxlink/state


[QsoRecorder]
REC_DIR=/var/spool/svxlink/qso_recorder
#MIN_TIME=1000
MAX_TIME=3600
SOFT_TIME=300
MAX_DIRSIZE=1024
DEFAULT_ACTIVE=0
#TIMEOUT=300
#QSO_TIMEOUT=300
ENCODER_CMD=/usr/bin/oggenc -Q \"%f\" && rm \"%f\"




[LocalLink]
CONNECT_LOGICS=SimplexLogic,MicLogic
DEFAULT_ACTIVE=1


[NetLogic]
TYPE=Repeater
RX=NetRx
TX=NetTx
CALLSIGN=DH1AA
EVENT_HANDLER=/usr/share/svxlink/events.tcl
OPEN_ON_SQL=20
IDLE_TIMEOUT=0
OPEN_SQL_FLANK=OPEN
NO_REPEAT=1


[NetLink]
NAME=Net
#CONNECT_LOGICS=SimplexLogic,NetLogic
CONNECT_LOGICS=SimplexLogic:34,NetLogic:35
DEFAULT_ACTIVE=1


[NetRx]
TYPE=Net
HOST=ip richtig
TCP_PORT=5300
AUTH_KEY=pwd
CODEC=OPUS
#OPUS_ENC_FRAME_SIZE=20
#OPUS_ENC_COMPLEXITY=10
#OPUS_ENC_BITRATE=20000
#OPUS_ENC_VBR=1
LOG_DISCONNECTS_ONCE=1


[NetTx]
TYPE=Net
HOST=ip richtig
TCP_PORT=5300
AUTH_KEY=pwd
CODEC=OPUS
#OPUS_ENC_FRAME_SIZE=20
#OPUS_ENC_COMPLEXITY=10
#OPUS_ENC_BITRATE=20000
#OPUS_ENC_VBR=1
LOG_DISCONNECTS_ONCE=1




[MicLogic]
TYPE=Simplex
RX=MicRx1
TX=MicTx1
CALLSIGN=DH1AA-E74DD
NOREPEAT=0
IDLE_TIMEOUT=10
OPEN_ON_SQL=20
DEFAULT_LANG=de_DE
EVENT_HANDLER=/usr/share/svxlink/events.tcl
OPEN_SQL_FLANK=OPEN


[MicRx1]
TYPE=Local
AUDIO_DEV=alsa:plughw:2
AUDIO_CHANNEL=0
#
#SQL_DET=VOX
#SQL_START_DELAY=0
#SQL_DELAY=0
#SQL_HANGTIME=500
#SQL_TIMEOUT=600
#VOX_FILTER_DEPTH=20
#VOX_THRESH=1000
#
SQL_DET=GPIO
GPIO_SQL_PIN=gpio9
#
#CTCSS_FQ=136.5
#SERIAL_PORT=/dev/ttyS0
#SERIAL_PIN=CTS:SET
#GPIO_SQL_PIN=gpio3
SIGLEV_SLOPE=1
SIGLEV_OFFSET=0
SIGLEV_OPEN_THRESH=30
SIGLEV_CLOSE_THRESH=10
DEEMPHASIS=0
DTMF_DEC_TYPE=INTERNAL
DTMF_MUTING=1
DTMF_HANGTIME=100
#DTMF_SERIAL=/dev/ttyS0


[MicTx1]
TYPE=Local
AUDIO_DEV=alsa:plughw:2
AUDIO_CHANNEL=0
PTT_TYPE=NONE
PTT_PORT=/dev/ttyUSB1
PTT_PIN=DTRRTS
TIMEOUT=3000
TX_DELAY=0
PREEMPHASIS=0
DTMF_TONE_LENGTH=100
DTMF_TONE_SPACING=50
DTMF_DIGIT_PWR=-15




[Macros]
1=EchoLink:853418#
2=EchoLink:967332#
3=EchoLink:819613#
4=EchoLink:558628#
5=EchoLink:558817#
6=EchoLink:232503#
7=EchoLink:740751#
8=EchoLink:6494#
9=EchoLink:9999# 


[Rx1]
TYPE=Local
AUDIO_DEV=alsa:plughw:1
AUDIO_CHANNEL=0
SQL_DET=GPIO
GPIO_SQL_PIN=gpio3
SQL_START_DELAY=100
SQL_DELAY=100
SQL_HANGTIME=500
#SQL_DET=SERIAL
#SQL_START_DELAY=0
#SQL_DELAY=0
#SQL_HANGTIME=0
#SQL_EXTENDED_HANGTIME=1000
#SQL_EXTENDED_HANGTIME_THRESH=15
#SQL_TIMEOUT=600
#VOX_FILTER_DEPTH=20
#VOX_THRESH=1000
#CTCSS_MODE=2
#CTCSS_FQ=136.5
#CTCSS_SNR_OFFSET=0
#CTCSS_OPEN_THRESH=15
#CTCSS_CLOSE_THRESH=9
#CTCSS_BPF_LOW=60
#CTCSS_BPF_HIGH=270
#SERIAL_PORT=/dev/ttyUSB0
#SERIAL_PIN=CTS
#SERIAL_SET_PINS=DTR!RTS
#EVDEV_DEVNAME=/dev/input/by-id/usb-SYNIC_SYNIC_Wireless_Audio-event-if03
#EVDEV_OPEN=1,163,1
#EVDEV_CLOSE=1,163,0
#GPIO_SQL_PIN=gpio3
#PTY_PATH=/tmp/rx1_sql
#HID_DEVICE=/dev/hidraw3
#HID_SQL_PIN=VOL_UP
#SIGLEV_DET=TONE
SIGLEV_SLOPE=1
SIGLEV_OFFSET=0
#SIGLEV_BOGUS_THRESH=120
#TONE_SIGLEV_MAP=100,84,60,50,37,32,28,23,19,8
SIGLEV_OPEN_THRESH=30
SIGLEV_CLOSE_THRESH=10
DEEMPHASIS=0
SQL_TAIL_ELIM=200
PREAMP=15
PEAK_METER=1
AUDIO_FILTER=HpBe1/1000
DTMF_DEC_TYPE=INTERNAL
DTMF_MUTING=1
DTMF_HANGTIME=100
#DTMF_SERIAL=/dev/ttyUSB0
#DTMF_PTY=/tmp/rx1_dtmf
#DTMF_MAX_FWD_TWIST=8
#DTMF_MAX_REV_TWIST=4
1750_MUTING=1
#SEL5_DEC_TYPE=INTERNAL
#SEL5_TYPE=ZVEI1
#FQ=433475000
#WBRX=WbRx1




[Tx1]
TYPE=Local
AUDIO_DEV=alsa:plughw:1
AUDIO_CHANNEL=0
#PTT_TYPE=SerialPin
#PTT_PORT=/dev/ttyUSB0
#PTT_PIN=RTS
PTT_TYPE=GPIO
PTT_PIN=gpio10
#PTT_HANGTIME=1000
TIMEOUT=300
TX_DELAY=500
AUDIO_FILTER=LpBe1/1000
#CTCSS_FQ=136.5
#CTCSS_LEVEL=9
PREEMPHASIS=0
DTMF_TONE_LENGTH=100
DTMF_TONE_SPACING=50
DTMF_DIGIT_PWR=-15
MASTER_GAIN=2.0


[LocationInfo]
APRS_SERVER_LIST=euro.aprs2.net:14580
STATUS_SERVER_LIST=aprs.echolink.org:5199
LON_POSITION=6.59.44E
LAT_POSITION=50.31.10N
CALLSIGN=EL-DH1AA
FREQUENCY=433.450
TX_POWER=2
ANTENNA_GAIN=6
ANTENNA_HEIGHT=5m
ANTENNA_DIR=-1
PATH=WIDE1-1
BEACON_INTERVAL=10
#TONE=136
COMMENT=SvxLink by SM0SVX (svxlink.sourceforge.net)

Display More

73 de dzevad dh1aa

DH9YAP · January 6, 2018 at 5:17 PM

Hi
Die MicroLogic findet deine Soundkarte nicht.

73 Jürgen

dh1aa · February 8, 2019 at 10:36 AM

Hallo

neuer Problem nach update.

Heute habe ich auf mehreren Systeme update durchgeführt es hat überall auf Raspberry gut geklappt leider auf Banana Pi starte nicht die Verbund kommt folgende Fehler raus:

Starting logic: ReflectorLogic

*** ERROR: Unknown logic type "Reflector"specified for logic ReflectorLogic.

*** WARNING: Logic ReflectorLogic has been specified in logic link ReflectorLink but that logic is missing. Removing logic from link.

Activating link ReflectorLink

MfG

dzevad

dh1aa · February 8, 2019 at 3:12 PM

Hallo

Eine Komplet neuer Installation von SVXLINK hat das Problem gelöst

73 dzevad

dh9yap · April 15, 2019 at 11:08 PM

Ich vermute du hattest svxlink nicht mit git pull aktualisiert !!

Hier ist es genau beschrieben:

https://svxlink.de/selber-kompilieren/

73 Jürgen funknetz.nrw

dh1aa · May 19, 2019 at 9:53 PM

Hallo

jetzt geht es Weiter mit Problem nach Update alles schön und gut geklappt leider wen ich mein Link konektiren über EchoLink dann stürzt gesamte Svxlink.

Svxlink ist mit git pull aktuelisiert ...

73 Dzevad

dh9yap · May 20, 2019 at 12:20 PM

Hi

Jetzt bin ich auch betroffen.

Das gleiche Problem !!

Das ist das Risiko wenn man einen Trunk installiert.

Am besten immer eine stabile Version.

Naja... schauen wir mal.

73 Jürgen

DJ9PH · May 20, 2019 at 8:51 PM

Hallo zusammen,

auch hier nochmal die Info: Betrifft auch DM0JL und DB0SZ.

Posts zum gleichen Thema:

Echolinkmodul

Inzwischen folgende zusätzlichen Infos um das Problem einzugrenzen:

Ausgehende Echolink Verbindung Log:

DTMF command received in module EchoLink: 31

Creating random connection to node:

KB1MMR-R ON 14:53 Durham, CT 313834 73.159.240.103

Connecting to KB1MMR-R (313834)

terminate called after throwing an instance of 'std::logic_error'

what(): basic_string::_M_construct null not valid

Eingehende Echolink Verbindung:

Spurious audio packet received from 89.15.237.191

Incoming EchoLink connection from DJ9PH (Christian) at 89.15.237.191

terminate called after throwing an instance of 'std::logic_error'

what(): basic_string::_M_construct null not valid

Abgebrochen

Bei der eingehenden Verbindung wird keine Sendertastung vorgenommen.

DJ9PH · June 8, 2019 at 9:23 AM

Hi together,

Adi posted a fix:

https://github.com/sm0svx/svxlink/issues/455

Thanks for the help Adi & 73!